Audio panels and intercom
Choose which radio you talk on and which ones you hear.
PS Engineering PMA6000B audio panel
In: N3355EN65673N51580N40SPN65626
Sets which radio your push-to-talk uses, which radios you hear, and how the intercom works.
Know the controls
- Transmit selector: picks the radio you talk on (COM 1 or COM 2).
- Receive buttons: turn on each radio you want to hear (COM, NAV, marker beacon).
- Intercom volume and squelch knobs for pilot and passengers.
- Intercom mode: isolate the pilot, or let everyone hear each other.
How to
- Talk to the tower on COM 1
- Set transmit to COM 1 and make sure COM 1 receive is on.
- Listen to the weather (ATIS) on COM 2
- Keep transmit on COM 1, turn on COM 2 receive, listen, then turn it back off.
- Identify a VOR station
- Turn on NAV 1 receive, listen for the Morse code, then turn it off.
- Stop intercom hiss
- Turn squelch until normal talking opens the intercom but engine noise does not.
Tip: If you hear nothing at all, check the transmit and receive buttons before blaming the radio. The pilot’s guide explains what still works if the panel loses power.
Full pilot’s guide (PDF)Know the controls
- Microphone buttons (COM 1 MIC, COM 2 MIC): pick the radio you talk on.
- Receive buttons: COM 1, COM 2, NAV 1, NAV 2 and marker beacon (MKR).
- Marker lights: blue (outer), amber (middle), white (inner).
- Intercom knob for volume and squelch; pilot and crew isolation buttons.
How to
- Talk on COM 1
- Press COM 1 MIC. Its receive turns on with it.
- Listen to ATIS on COM 2
- Leave COM 1 MIC selected, press COM 2 receive, listen, then press it again to turn it off.
- Identify a VOR
- Press NAV 1 receive, confirm the Morse code, then turn it off.
- Quiet the passengers during a busy moment
- Use the pilot isolation mode so only you hear the radios.
Tip: A lit button means it is on. Glance at the panel before every flight so you know what you will hear.
Full pilot’s guide (PDF)Know the controls
- Transmitter selector: COM 1 or COM 2.
- Audio toggle switch for each radio: speaker, off, or phone (headset). Check the labels on the panel.
- Marker beacon lights: blue (outer), amber (middle), white (inner).
- Marker sensitivity (HI/LO) and a test position for the lights.
How to
- Talk to the tower on COM 1
- Set the transmitter selector to 1 and switch COM 1 audio to phone.
- Hear a second radio
- Switch that radio’s audio toggle to phone, then back to off when finished.
- Test the marker lights
- Hold the switch to test and confirm all three lights work.
Tip: Most “dead radio” problems in this airplane are an audio switch left on off or speaker. Check them first.
Full pilot’s guide (PDF)GPS and navigation/communication radios
Talk to the tower, tune navigation stations and fly the GPS.
Garmin GNS 430W GPS/nav/com
In: N3355EN65673N51580N40SPN65626N107TS
Your main radio and GPS: COM 1 for talking, NAV 1 for VOR and ILS, and GPS for direct-to, flight plans and approaches.
Know the controls
- Top-left knob: power and COM volume. Knob below it: NAV (VLOC) volume.
- Bottom-left knobs: tune the standby frequency. Push the small knob to switch between COM and NAV.
- Flip-flop keys (two arrows): swap the standby frequency into active.
- Right knobs: large knob picks the page group (NAV, WPT, AUX, NRST), small knob picks the page.
- Keys: D→ (direct-to), CDI, OBS, MSG, FPL (flight plan), PROC (procedures), CLR, ENT.
How to
- Start up
- Turn on with the avionics master, let the self-test finish, check the database dates, press ENT.
- Tune a frequency
- Dial it into standby with the left knobs, then press the COM flip-flop key.
- Go direct to an airport
- Press D→, enter the identifier with the right knobs, press ENT, then ENT again to activate.
- Find the nearest airport
- Turn the large right knob to the NRST pages.
- Fly a VOR or ILS on the needle
- Tune and activate the NAV frequency, then press CDI until it shows VLOC.
- Get back to the map fast
- Press and hold CLR.
Tip: Before you follow the needle, check whether the screen says GPS or VLOC. Following the wrong one is a common student mistake. Holding the COM flip-flop key for about 2 seconds sets the emergency frequency, 121.5.
Full pilot’s guide (PDF)Know the controls
- Each side shows an active frequency and a standby frequency.
- Transfer button (two arrows) on each side swaps standby and active.
- Large knob changes the whole numbers, small knob changes the decimals.
- Power and volume knob on the COM side.
How to
- Set the next frequency early
- Dial it into standby while you are still on the current one, then press transfer when told to switch.
- Listen to ATIS
- Tune ATIS on COM 2, turn on COM 2 receive on the audio panel, keep transmit on COM 1.
- Use NAV 2 for a cross-check
- Tune a VOR on the right side, identify it, and set the course on the #2 indicator.
Tip: Some frequencies end in .x25 or .x75. If you cannot reach one, check the guide for how this radio steps through those in-between channels.
Full pilot’s guide (PDF)Know the controls
- One COM frequency and one NAV frequency. There is no standby window.
- Turning a frequency knob changes the live frequency right away.
- Power, volume and squelch knobs.
How to
- Change frequency
- Finish your radio call first, then turn the knobs to the new frequency and read it back.
- Check the radio works
- Turn squelch until you just hear static, then back it off until it is quiet.
- Use NAV 2
- Dial in the VOR, turn on NAV 2 receive on the audio panel, identify it, then set the course.
Tip: Because there is no standby, write the next frequency down instead of pre-setting it in this radio.
Full pilot’s guide (PDF)Know the controls
- One COM frequency and one NAV frequency on rolling number displays. There is no standby window.
- Turning a frequency knob changes the live frequency right away.
- Power, volume and squelch knobs.
How to
- Change frequency
- Finish your radio call, then dial the new frequency and double-check the numbers.
- Listen to ATIS without losing the tower
- Use the other radio for ATIS, with transmit left on the tower radio.
- Use the NAV side
- Dial in the VOR, identify the Morse code, then set the course on the indicator.
Tip: In N5285V both radios are this type, so plan which one you will use for the tower and which for ATIS before you start the engine.
Full pilot’s guide (PDF)Transponders and Automatic Dependent Surveillance–Broadcast (ADS-B)
Let air traffic control (ATC) and other airplanes see you.
Stratus ES/ESG transponder with ADS-B Out
In: N3355EN65673N51580N40SPN65626N107TS
Answers ATC radar with your code and altitude, and broadcasts your position (ADS-B Out).
Know the controls
- Number keys to enter a four-digit code (digits 0 to 7 only).
- VFR key: sets 1200 in one press.
- Mode: standby, on, or altitude reporting (ALT).
- IDENT key: makes your target flash on the controller’s screen.
How to
- Set a code ATC gives you
- Enter the four digits, then read the code back to ATC.
- Fly without a code (VFR)
- Press the VFR key to set 1200.
- Before takeoff
- Confirm the right code and altitude mode (ALT).
- When ATC says “ident”
- Press IDENT once. Only when asked.
Tip: Codes to know: 1200 VFR, 7500 hijack, 7600 lost radio, 7700 emergency.
Full pilot’s guide (PDF)Know the controls
- Mode knob: OFF, SBY (standby), ON, ALT (altitude reporting), TST (test).
- Four small knobs set the code, one digit each.
- IDT button: makes your target flash for the controller.
- Reply light blinks when radar asks the transponder a question.
How to
- Before takeoff
- Set the code, then turn the mode knob to ALT.
- Change the code
- Turn the digit knobs one at a time, avoiding 7500, 7600 and 7700 on the way.
- Test it
- Turn to TST and check the reply light comes on.
Tip: This transponder also feeds the SkyBeacon ADS-B Out unit, so a wrong code or wrong mode shows up there too.
Full pilot’s guide (PDF)Know the controls
- No pilot controls in the cockpit.
- It uses the code and mode you set on the KT 76A transponder.
How to
- Make sure it is working
- Set the transponder to ALT with the correct code. Ask the office if the airplane has a status report.
Tip: There is no SkyBeacon guide in the study library yet. Ask the office or your instructor.
Stratus ADS-B receiver (traffic and weather)
In: N3355EN65673N51580N40SPN65626N107TS
Sends nearby traffic and weather (ADS-B In) to your tablet app, such as ForeFlight.
Know the controls
- Connects to your tablet over Wi‑Fi.
- Status lights show power and data.
How to
- Connect your tablet
- Join the Stratus Wi‑Fi network, open your app, and check it shows the Stratus as connected.
- Use traffic
- When a target shows up, look outside for it. The screen helps you find it; your eyes confirm it.
Tip: Weather from ADS-B can be several minutes old. Use it to stay away from storms, never to pick a path through them.
Full pilot’s guide (PDF)Emergency Locator Transmitters (ELT)
The beacon that helps rescuers find the airplane.
Dorne & Margolin DM ELT 6C
In: N3355EN65673N51580N65626N107TS
Turns on by itself in a crash and transmits on 121.5 so rescuers can find the airplane.
Know the controls
- Panel switch: leave it in ARM for every flight.
- ON turns it on by hand in an emergency.
How to
- After landing
- Listen on 121.5 for a few seconds to make sure the ELT is not going off.
- If it went off by accident
- Follow the guide’s reset steps, then tell the office so ATC can be notified.
- Testing
- Only in the first 5 minutes after the hour, and no more than three sweeps of the tone.
Tip: A hard landing can set off an ELT. A quick listen on 121.5 before shutdown saves a search.
Full pilot’s guide (PDF)Know the controls
- Panel switch: leave it in ARM for every flight.
- ON turns it on by hand in an emergency.
How to
- After landing
- Listen on 121.5 for a few seconds to make sure the ELT is not going off.
- If it went off by accident
- Follow the guide’s reset steps, then tell the office so ATC can be notified.
- Testing
- Only in the first 5 minutes after the hour, and no more than three sweeps of the tone.
Tip: A hard landing can set off an ELT. A quick listen on 121.5 before shutdown saves a search.
Full pilot’s guide (PDF)No avionics listed for this airplane yet.
Know the airplane, too
Speeds, limits, emergency procedures and performance for the 172N, 172P and 172RG.